If your dining room chair cushions are looking a little worse for wear, it might be time to reupholster them. This is a relatively easy project that anyone can do, and it will make your chairs look like new again. <\/p>\n \n
Assuming you’re talking about reupholstering chair cushions: \n\nThe first step is to remove the old fabric. This can be done by carefully cutting around the edge of the fabric with a sharp knife, being careful not to cut into the padding underneath.
Once the fabric is removed, you’ll need to remove any staples or tacks that are holding the padding in place. Now it’s time to measure your new fabric. You’ll want to add an extra inch or two all the way around so you have plenty of material to work with.
Cut your new fabric and lay it out on a flat surface. Place the old cushion on top of the new fabric and use a pencil to trace around it. Now you’re ready to start stapling!
Start in the middle of one side and work your way around, making sure to pull the fabric tight as you go. Once you get all the way around, trim off any excess material and voila – you’ve got yourself a brand new chair cushion!<\/p>\n \n
It cost about $40 to reupholster a dining room chair cushion. The process usually takes about an hour, and requires some basic sewing skills. You will need to purchase fabric and batting, and have a few tools on hand, including a seam ripper, scissors, and a straight edge.<\/p>\n \n
When you are reupholstering dining chairs, the best fabric to use is a heavy-duty upholstery fabric. This type of fabric is durable and can withstand a lot of wear and tear. It is also easy to clean, which is important if you have kids or pets.
Another advantage of using a heavy-duty upholstery fabric is that it will not show dirt or stains as easily as lighter fabrics.<\/p>\n \n
When it comes to reupholstering a dining chair cushion, the amount of fabric you will need will depend on the size of the cushion and whether or not you are also covering the welting. In general, you will need 1 yard of 54-inch wide fabric for each seat cushion, plus an additional half yard if you are also covering the welting. If your cushions are larger or if you plan on using a patterned fabric, you may need more fabric. \n\n
To determine how much fabric you need, start by measuring the length and width of your seat cushion. Then, add 6 inches to each measurement to account for the seam allowance. For example, if your seat cushion measures 16 inches by 16 inches, you will need 2 yards of fabric (1 yard for each side plus an additional 2 inches for the seam allowance). \n\n
If your chair has Welting:\nIn addition to measuring the length and width of your seat cushion, you will also need to measure the perimeter of your seat cushion. To do this, simply add up all four sides of your cushion (length + width + length + width).
For our 16-inch by 16-inch example above, this would give us a perimeter measurement of 64 inches. \n\nNow that we have both our measurements (area and perimeter), we can calculate how muchfabricwe’ll need to cover ourseatcushionandweltingbyusingtheformula: area + perimeter + 1\/2″. So forour16″ x 16″cushionwith 64″ofperimeterwewouldneed(16×16)+(64)+(1\/2)”or17yardsoffabric!<\/p>\n \n
<\/p>\n \n
Have you ever grown attached to a piece of furniture, only to have it fall apart on you? It\u2019s happened to all of us at some point or another. But instead of relegating your beloved chair to the trash heap, why not give it new life by reupholstering it with foam?\n\n
Here\u2019s how:\n\n1. Remove the old fabric from the seat of the chair. Be careful not to tear the fabric if you plan on using it as a template for your new foam.
If the fabric is in too bad of shape, simply use a similar-sized piece of muslin as your template.\n\n2. Cut out your new foam using your template as a guide. Make sure to leave about an inch around all sides so that you have enough room to staple the fabric in place later on.\n\n
3. Place the foam onto the seat and begin stapling the fabric into place, working from the center outwards so that everything remains tight and pulled taut. Don\u2019t forget to wrap those staples around to the underside of the chair so that they don\u2019t poke through and scratch anyone who sits in it!\n\n4. Once all four sides are done, flip the chair over and admire your handiwork!
Your old faithful friend is now good as new (or even better).<\/p>\n \n
If you have a chair with a removable seat, upholstering it is a relatively easy process. But what do you do if your chair doesn’t have a removable seat? You can still upholster it, but it’s a bit more of a challenge.
Here’s how to do it:\n\n1. Remove the old fabric from the seat. This may require some careful cutting and scraping, depending on how the original fabric was attached.\n\n
2. Cut new fabric to size, allowing for extra material to tuck under the edges of the seat.\n\n3. Attach the new fabric to the seat using either staples or adhesive spray. Be sure to pull the fabric tight so there are no wrinkles or looseness in the finished product.\n\n
4. Trim away any excess fabric, then reattach any buttons or other embellishments that were on the original seat cover.<\/p>\n \n
Assuming you have a basic understanding of upholstery and sewing, these instructions will show you how to reupholster a chair cushion. You will need:\n\n-1\/2 yard of fabric (this will depend on the size of your cushion)\n
-Staple gun & staples\n-Scissors\n-Upholstery foam (can be found at most craft stores)\n
-Plywood (optional)\n-Muslin (optional)\n \nInstructions:\n\n
1. Remove the old fabric from the cushion, being careful not to rip or tear it. If the fabric is in good condition, you can use it as a pattern for cutting out your new fabric. Otherwise, make a paper template of the shape of your cushion.\n\n
2. Cut out your new fabric using the template or old fabric as a guide. If you are using patterned fabric, be sure to cut it so the design is positioned correctly when finished.\n\n 3. Place the new piece of fabric right side down on a flat surface.
Center your upholstery foam on top of the wrong side of the fabric, then cover with muslin or another layer offabric if desired. This will give your finished product a neater appearance and prolong its lifespan.\n\n 4. Begin stapling one side of the muslin\/fabric to the underside ofthe plywood seat base, pulling taut as you go but taking care not to stretchthe material too much (which could cause it to tear).
When you reachthe corners, fold them neatly like you would wrapping a present, thencontinues stapling around all four sides until complete. <\/p>\n \n
If you have a dining chair with a cushion that needs some love, don’t despair! You can easily reupholster the cushion to give it new life. Here’s how:\n\n
1. Remove the old fabric from the cushion, being careful to remove any staples or tacks.\n\n2. Cut new fabric to size, allowing for extra material to wrap around the sides of the cushion.\n\n3. Attach the new fabric to the cushion, using either staples or tacks.
Be sure to pull the fabric tight so there are no wrinkles or sagging spots.\n\n4. Trim away any excess fabric, then sit back and enjoy your newly upholstered dining chair cushion!<\/p>\n \n