If you have a Graco high chair, you may eventually need to fix the tray. The tray is what your child sits on and it can become worn or damaged over time. There are a few things you can do to fix a Graco high chair tray.
With a little bit of effort, you can make your high chair look like new again.
- Unscrew the four bolts on the underside of the tray using a Phillips head screwdriver
- Remove the old tray and set it aside
- Place the new tray on the high chair frame, making sure that the plastic tabs on the sides of the tray fit into the slots on the frame
- Screw in the four bolts underneath the tray, using a Phillips head screwdriver
- Do not overtighten them, as this may strip out the threads in the bolts or breakthe plastic tabs onthe side ofthe tray
Graco High Chair Tray Replacement
If you have a Graco high chair, you may be wondering how to replace the tray. The good news is that it’s actually quite easy to do! Here are the steps:
1. Remove the old tray by unscrewing the two screws that hold it in place.
2. Place the new tray in position and screw it in place.
3. That’s it!
Your Graco high chair is now ready to use with its new tray.
Graco High Chair Straps
If you have a little one at home, then you know how important it is to have a high chair that they can sit in. But what about when they start to squirm and wiggle around? That’s where the Graco High Chair Straps come in!
These straps are designed to keep your little one safe and secure in their high chair, so you can have peace of mind knowing that they’re not going to fall out. They’re easy to install and use, and they’ll make sure that your child is always sitting comfortably and securely.
So if you’re looking for a way to keep your little one safe in their high chair, then be sure to check out the Graco High Chair Straps!
Graco High Chair Straps Instructions
If you have a Graco high chair, it is important to know how to properly strap your child in. Here are some step-by-step instructions:
1. Place the high chair on a flat surface.
Make sure that the back of the chair is facing you.
2. Take the shoulder straps and thread them through the slots on either side of the backrest.
3. Cross the straps in the middle of the backrest and pull them tight.
The straps should be snug against your child’s shoulders, but not too tight.
4. Take the waist strap and thread it through the slot in the front of the seat bottom. Pull it up between your child’s legs and fasten it to the other side of the seat bottom.
Again, make sure that this strap is snug but not too tight.
5 Finally, adjust both sets of straps so that they are at a comfortable level for your child’s height.
Graco High Chair 4-In-1
If you’re looking for a versatile high chair that will grow with your child, the Graco 4-in-1 High Chair is a great option. This chair can be used as a traditional high chair, with a tray for feeding, or without the tray as a booster seat. It also converts to a youth chair, making it perfect for kids who are ready to sit at the table with the family.
The Graco 4-in-1 High Chair is easy to assemble and clean, and it’s available in several different colors to match your décor.
How Do You Take Apart a Graco High Chair Tray?
When it comes to taking apart a Graco high chair tray, there are a few things that you need to keep in mind. First of all, you will need to remove the screws that are holding the tray onto the chair. Once you have removed the screws, you will then need to take off the plastic cover that is covering the bolts.
After you have done this, you will be able to see the bolts that are holding the tray onto the chair. You will need to use a wrench to loosen these bolts so that you can remove the tray from the chair.
Why were Graco High Chairs Recalled?
On July 17, 2014, Graco Children’s Products Inc. announced the recall of 11 models of their high chairs. The reason for the recall was that the plastic tray insert could become detached from the chair, posing a fall hazard to young children. Over 700,000 units were affected by the recall in the United States and Canada.
This isn’t the first time Graco has had to deal with issues regarding their high chairs. In 2010, they recalled over 4 million units due to a similar problem with the tray inserts becoming detached. However, this most recent recall is much smaller in scope.
If you have one of the affected high chairs, you should stop using it immediately and contact Graco for a free replacement tray insert. For more information on this recall, you can visit Graco’s website or contact their customer service line at 1-800-345-4109.
How Do You Put a Tray on a High Chair?
When you have a baby or toddler, one of the pieces of essential equipment you will need is a high chair. A high chair enables your little one to sit at the table with the rest of the family and eat solid foods. But how do you put a tray on a high chair?
The first step is to find a tray that fits your particular high chair model. There are many different sizes and shapes of trays available, so it’s important to get one that’s specifically made for your high chair. Once you have the right size tray, simply place it on top of the high chair seat.
Make sure that the tray is locked into place so that it doesn’t slip off when your child is eating.
If your high chair has a removable tray, then putting it on is even easier. Simply lift up the tray and snap it into place on the top of the seat.
Again, make sure that it’s locked in securely before letting your child use it.
With either type of tray, you may want to put a placemat or piece of cloth down first before adding any food.
How Do You Disassemble a Graco 6 in 1 High Chair?
Assuming you would like a step-by-step guide on how to disassemble a Graco 6 in 1 high chair:
1. Begin by removing the tray from the high chair. To do this, press the two silver buttons on either side of the tray.
The tray will then unlatch and can be lifted off of the high chair.
2. Next, remove the seat back and cushion from the high chair. To do this, first loosen and remove the two screws that are located at the top of the seat back (behind where the tray was attached).
With these screws removed, you should then be able to lift the seat back up and off of the high chair. The seat cushion is attached to the seat back with Velcro, so it will come off along with the seat back.
3. The final step is to remove the legs from the high chair base.
There are four legs total – two in front and two in back. Each leg is held in place by a large plastic nut. Use your hands to unscrew each nut until it is completely removed from its respective leg (you may need help with this step).
Conclusion
If your Graco high chair tray is giving you trouble, there are a few things you can do to fix it. First, make sure that the tray is locked into place. If it’s not, simply push it until you hear it click.
If that doesn’t work, try removing the tray and then reinstalling it. Finally, if all else fails, you can contact Graco customer service for further assistance.
